Brakelight switch for rear brake pedal

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8112996

Also fits Aprilia, CAPONORD 1000 ETV 1000, Aprilia, PEGASO 650, Aprilia, RS 250. Aprilia, RST FUTURA, Aprilia, RSV 2 1000, Aprilia, RSV 4 1000 RSV4 1000RR, Aprilia, SHIVER 750, Aprilia SHIVER 750 SHIVER 750, Aprilia TUONO 1100 RR RSV 1100 TUONO V4

Speedo sensor with 100cm lead and 3 pin plug for non-ABS models

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8124528

Also fits Aprilia Falco (2000-2003)

Brand new genuine Valeo starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016
Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

This is a genuine Valeo starter made in the EU- please do not confuse with the cheap Chinese copies that sometimes appear on eBay.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Please note you can get a discount of £30 on this item if you part exchange your existing faulty starter motor. See ELA30837 for less expensive alternative part

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Support for oil temperature sensor

 This part is available by special order, request a quote

 03163330 GU03163330 03 16 33 30
 0316 3330 0316.3330 03.16.33.30

Sidestand cutout switch

See ELA81319 for rotary switch that was fitted to some models

 This part is available by special order, request a quote

 639542 MG639542

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote

Cut out switch, threaded body. Used as sidestand switch on big twins and clutch cut out switch on V7 series small twins and Breva 750

 This part is available by special order, request a quote

 29759150 GU29759150 29 75 91 50
 2975 9150 2975.9150 29.75.91.50

Lambda sensor with 660mm lead

 This part is available by special order, request a quote

 896110 MG896110

Regulator rectifier with twin plugs, 3 yellow wires to white connector, 4 wires to black connector

 This part is available by special order, request a quote

2D000043

Round 12v two pin flasher relay for LED indicators. For use with aftermarket LED indicators

Includes rubber for attaching to bike.

NB Only suitable for LED indicators. Will not work in modern V7 models because these do not utilise a flasher unit.

 This part is available by special order, request a quote